BI-LED: MORIMOTO M LED
Output: We'll just start with the hotspot. It's on par with the Mini D2S 4.0 and a XB 45K Bulb / XB55 ballast, and about 20% brighter than it's closest LED-based competitor: the i-lens. The Kuria optic clear lens and curved cutoff shield produce a beam pattern that's plenty wide, with an ECE-sloped cutoff that's super sharp, colorful. Rather than off-the-shelf LED's like early LED projectors in the aftermarket, the MLED uses a specially developed CSP chipset from Seoul SemiConductor. To top it all off, the "M" icon that's projected onto the ground thanks to the special foreground limiter is just plain cool.
Physically: It has a lot going for it too. The threaded mounting shaft can be removed from the projector to free up almost an inch of depth for those who don't need/want it. The integrated mag-lev fan is sunk into the heat sink, keeping space to a minimum without sacrificing the ability to stay cool. The wiring is clean, out of the way, and can be disconnected with ease. The precision and existence of mostly die-cast (rather than stamped) parts in the cutoff shield mechanism makes for a slop-free setup and conveys quality over cost savings. It could pass for an OEM part.
Simplicity: Forget about separate bulbs. Forget about big ballasts, or where to mount them. Forget about complex relay harnesses, and where to run them. Here, you've got the projector and a small external LED driver to regulate power and control it's low and high beam function. If you're a clutter phobe, or simply tight on space working on something like a motorcycle: the MLED is the way to go.
Easy to Install: On a H4-based headlight reflector for example...Remove the headlight lens, insert the threaded mounting shaft through the pre-existing hole in the back of the reflector, add the alignment plate, tighten the lock ring, and re-seal the headlights. For other applications, minimal cutting will probably be involved but you'll find the results well worth it!
Worth it?If you want the latest and greatest, Yes. It is. Want to produce about the same amount of light output for your money? The Morimoto Mini D2S 4.0 is probably better for you - only because it's less expensive. But consider this: Yeah, the Morimoto M-LED projectors are expensive, but unlike an HID-based retrofit, you wont need bulbs, ballasts, in many cases a wire harness. You just need some shrouds, and that's about it! The rest is here.
Benchmark: Morimoto. The Automotive Lighting Benchmark. We are globally recognized as the brand to beat. No other brand blends performance and genuine product quality quite like us. Our vast product line has something for nearly every application, and if not; our R&D department is capable of producing it in short order. Contact us and learn what we can do for you!
|PROJECTORS:||2x Morimoto M LED Bi-LED|
|LED DRIVERS:||2x M LED Hi/Lo Control|
|HARDWARE:||2x Threaded shafts w/ lock rings|
|DIRECT FITMENT:||H4 Headlights (little/no mods required)|
|MODS REQUIRED:||H1,H7,H11,H13,9005,9006,9007 housings|
|BOLT PATTERN:||Morimoto Mini D2S 4.0 Standard|
|INPUT VOLTAGE:||9-16V DC|
|OUTPUTS:||Low and High Beam|
|UNITED STATES:||LHD (Left Hand Drive)|
|SHROUDS:||All Styles Except "Mini" or "Square"|
|CENTRIC RINGS:||Not Required|
|WIDTH:||94mm (105mm w/ tabs)|
|DEPTH:||148mm (w/ shaft)|
|DEPTH:||133mm (w/o shaft)|
|LENS DIAMETER:||3.0" round|
|HOUSING DEPTH:||121mm Minimum|
|STANDARD LENS:||100% clarity "Kuria Optic" glass|
|BOLT PATTERN:||:D2S 4.0 Standard|
|LED CHIPSET:||Seoul SemiConductor Proprietary 12TCSP|